SpeedyBee F405 V4 Flight Controller

$71.00

FAST DIspatch & Global delivery
Quality Assured Brand Manufacturer

SKU: SB-F405-V4 Category: Racing & Flight Sim Hardware - Steering Wheels / Pedals / Shifters / Accessories. Tag: Shopify Collective, Unmanned Tech

Description
Product Reviews

🚀The FPV Struggle is Real!

So, you're an FPV pilot with dreams as high as the stratosphere, huh? Well, we both know the struggle. You juggle between a dozen apps, your flight logs are messier than a toddler's bedroom, and "Battery Anxiety" might as well be your middle name. Frankly, it's easier herding cats than getting your flight setup juuuust right.

🌈 Imagine if Tony Stark Built Flight Controllers

What if your flight controller wasn't just a piece of hardware but a dedicated flight manager? One that could handle your black box, manage your ESCs, and still have enough power left over to throw a virtual high-five. A board so smooth, even your quad would swipe right.

🎉 The SpeedyBee F405 V4 30x30—The Symphony of Flight Perfection!

Behold the SpeedyBee F405 V4 30x30 Flight Controller. It's like the Swiss Army knife of the FPV world, just without the awkward toothpick.

✨ Key Highlights

Turbocharged STM32F405 CPU : Because the '90s called, and they want their F411 back.
Built-in 4-Level Battery Indicator : Say "peace out" to LiPo checkers and squinting at minuscule LED indicators.
Blackbox SD Card Slot : With support for 4GB of memory, you can log enough flights to give the black box of Air Force One a run for its money.
Onboard Bluetooth + SpeedyBee App : Why be tied down? Go wireless and tweak your setup with your smartphone like the millennial you are.
MaxLinear's Power Chip : You'd think it's overkill, but when you're pulling those maneuvers, you need stability that even a tightrope walker would envy.

🛠 Specs for the Tech-Savvy

Product Name	SpeedyBee F405 V4 30x30 Flight Controller
MCU	STM32F405
IMU(Gyro)	ICM42688P
USB Port Type	Type-C
Barometer	Built-in
OSD Chip	AT7456E chip
BLE Bluetooth	Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
WIFI	Not supported
DJI Air Unit Connection Way	Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug	Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot	*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
Current Sensor Input	Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.
Power Input	3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output	9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.
9V Output	2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.
3.3V Output	Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output	Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal	M1 - M4 on bottom side and M5-M8 on front side.
UART	6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry	UART R5(UART5)
I2C	Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad	Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer	BZ+ and BZ- pad used for 5V Buzzer
BOOT Button	Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input	Supported. Named as RS on the front side.
Smart Port / F.Port	Not supported
Supported Flight Controller Firmware	BetaFlight(Default), INAV
Firmware Target Name	SPEEDYBEEF405V4
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	41.6(L) x 39.4(W) x 7.8(H)mm
Weight	10.5g

🌐 One App to Rule Them All

Say goodbye to the tedious setups and calibration. With the SpeedyBee App, your smartphone becomes the ultimate FC configurator. We're talking pitch, yaw, roll, and even that crazy trick you're scared to tell your friends about. All configurable, right from your phone. Seriously, what's not to love?

⚡ Clean Power = Clean Flights

Did we mention surge protection is upped by 320%? Yeah, you read that right. With dedicated power supply to the gyroscope, even your most daring stunts will feel like a walk in the park.